|24th April 2008 02:08 PM|
What is a "spam firefight?"
And did I tell you I'm a big Jerry Garcia fan?
|24th April 2008 10:32 AM|
100% sure...... no!
That's why I sent off a personal email to the IT folks at
When they get back to me, then I'll be 100% sure, one way or the other.
By the way, "Mediator" does not seem to be "registered".
Perhaps there's a clue in that fact alone.
|23rd April 2008 07:12 AM|
Are you 100% sure, Roger?
You are aware that there are others at Starboard that view this forum?
|22nd April 2008 10:13 PM|
As a moderator on these forums, I'm fairly sure that "moderator" (#4) and "moderately" (#6) are hecklers just trying to start something (some sort of spam firefight perhaps).
If there was offense taken by one of the moderators at Starboard, they would have used
If they were really offended, they would have simply removed the thread.
The original poster could have chosen his words a little more wisely, but I doubt anyone
is truly "offended".
|22nd April 2008 05:46 PM|
but isnt using "F@%k " a way to be not offensive.
If you wanted to offensive you would have just written the real word.
WTF- or am I allowed to say that on the " free forums" ?
|22nd April 2008 09:23 AM|
Ummmmm..... what do you mean "do not use the screw supplied"?
Or....are you talking about some screw supplied with the NP RS-X base?
AFAIK no screw or base is supplied with the Phantom.
The entire mast track system is a "knock off" of the others I mentioned, made to a Cobra specification, and the pin is slightly different.
I had to ask Starboard HQ to get me the correct pin/universal assembly from the same supplier that made the mast track for the Phantom 301 I had last year.
Once I got the correct part, you simply insert the base and lock it down with the little black plastic actuator tab at the front of the mast track car.
Check this URL to see if you have the same board I'm familiar with:
If you have something different, then I may be incorrect, but both the Phantom and the Phantom Race proto I had last year had the same adjustable mast track, made to the Cobra specification and it required the "special" pin.
The pin for the Exocet race boards (with a sliding mast track) were the closest, but the correct part fit very nicely and was very secure.
It may indeed be the same pin set up as the RS-X Olympic board, but I did not try an RS-X base in either of the Phantoms I had.
As to "how the ?? do you put in the mast base, that's easily answered.
Get the correct pin/universal setup and then it fits just like any other board with a pin type (on the bottom, not a Euro Pin top) sliding mast track setup.
The pin bases I was supplied with came with the "special" Cobra pin on the bottom and a std. Euro pin on the top, with a WSH/Chinook/US adapter over the Euro pin on the top.
Only problem I had was the locking slider for the adapter tended to get stuck with the downhaul line if you were not careful to put the line up the back and the lock plate tab on the front.
Hope this helps,
|21st April 2008 05:00 PM|
Totally agree with "how the ! do you put in the base".
Moderator has not tried it.
|21st April 2008 07:33 AM|
If you continue to disobey forum rules
and use foul language, including anocryms, we reserve the right to block your IP address.
|21st April 2008 05:58 AM|
QUOTE "We have posting policies here...."
WTF? That is why he didnt write the f word in full, but hid it with different characters.
|20th April 2008 12:05 PM|
Please refrain from foul language.
We have posting policies here....
|This thread has more than 10 replies. Click here to review the whole thread.|