Go Back   Starboard Forums > Free Forum > HPL Older Carbon Rear End Wanted

Thread: HPL Older Carbon Rear End Wanted Reply to Thread
Your Username: Click here to log in
Image Verification
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Additional Options
Miscellaneous Options

Topic Review (Newest First)
30th December 2009 05:37 AM
G-42
Quote:
Originally Posted by Vincent View Post
Hi. Just in case somebody out there has broken an older HPL carbon race boom, but still has the carbon rear end in good shape, I'm interested in buying the rear end. Specifically I'm looking for the older "Race" rear end with the squared off tail and 4 pulleys sandwiched into the squared off carbon tail piece. This if before they did the monocoque tail. My boom is a 2004(?) blue "Hybrid Carbon Race 220". The tail has 60 cm of adjustment range. Thanks!
Vincent,
if you can't find a rear end, and if the extension tubes on your rear end are still OK (i.e, the break occured in the actual tail piece, so you can cut the tube at the joint to the old broken tail piece and salvage them, albeit at a wee bit shorter length), you can fashion your own tail end pretty easily with a bunch of carbon tape and something to use as a spacer (a block of marine-grade plywood should work great). Then you just bolt a few blocks to that new end-piece and you're good to go.

The way to set it up is to create a block of wood approximately 4" long, 1" thick, and 2" deep. Sand the wood to create a groove that nestles against the tubes on the side. Set the boom up on a work table and super-glue the block of wood to the tubes. Then start wrapping the whole contraption with 3 or 4 inch-wide carbon tape (wet that down with epoxy first on a sheet of plastic, then roll the wetted carbon with your hands wearing gloves, then do the wrapping). You'll want at least four or five layers of carbon at the joints, and you'll want the whole thing pretty tightly wrapped. Then wrap it in peelply, and then finish the job with a very tight wrap of electrical tape (poor man's vacuum bag). Cure overnight, than peel off the tape and peel play, mount your blocks, and when anybody raises an eyebrow, just explain to them how the old tail piece was just too wimpy and low performance for you.

You could even make the tail piece wider this way (just use a 6" or maybe even 8" long block of plywood) but for a 220+ boom, that's probably going to be less crucial than for a really long one.

I've seen a couple booms salvaged that way, and it seems to work pretty well.

-Andreas
http://g-42.blogspot.com
23rd December 2009 07:09 AM
joe_windsurfer hey bud:

i just purchased one used
so, obviously do NOT have the piece you need, but instead have some questions...

q1) how did you like it ? seems you did cuz you wish to continue to use it
q2) how much carbon is there actually in the boom? my impression was 20% , but the seller says it IS a carbon boom ??

thx
joe windsurfer
25th August 2009 03:20 AM
Vincent
HPL Older Carbon Rear End Wanted

Hi. Just in case somebody out there has broken an older HPL carbon race boom, but still has the carbon rear end in good shape, I'm interested in buying the rear end. Specifically I'm looking for the older "Race" rear end with the squared off tail and 4 pulleys sandwiched into the squared off carbon tail piece. This if before they did the monocoque tail. My boom is a 2004(?) blue "Hybrid Carbon Race 220". The tail has 60 cm of adjustment range. Thanks!

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT +7. The time now is 04:37 PM.