Go Back   Starboard Forums > Free Forum > Shrinking boxes

Thread: Shrinking boxes Reply to Thread
Your Username: Click here to log in
Image Verification
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Additional Options
Miscellaneous Options

Topic Review (Newest First)
20th September 2007 12:37 AM
Unregistered I have, fitted better than the 2 drake fins supplied with the iS133, no sanding whatsoever
19th September 2007 04:56 PM
cj0ne2 ....never bought a Select fin that fitted first time!
I have always had to sand them down quite a lot.
19th September 2007 03:21 PM
Unregistered
Quote:
Originally Posted by martwald View Post
With an electric sander the process doesn't take too long so I'm not overly bothered the time, suffice to say I've another Falcon in the post to me.

My concern however is that you could sand too much off one side or do it at an angle resulting in a fin which is very precise in its design not having the expected laminar flow over it, although I doubt this would have any noticeable effect.

I'm off to gps-speedsurfing to ask the same question.
hahahahahaha- like anyone would notice!
30th August 2007 07:14 AM
Unregistered The Rubber mallet has worked for me . Some of my customers have thought they needed to sand the fins l supplied because they were so tight. l am saying that chinook boxes are a good standard size, and other brand boxes may varie. Maybe l haven't come across a brand of fin that is way out, even select fins fit. Just try a gentle tap and see if things give. These are wave boards though.
You will learn more from questions than insults.
29th August 2007 11:15 PM
Unregistered No, the mullet gets in the way
29th August 2007 09:48 PM
martwald
rubber mallet

Are you sure you don't just use yer head
29th August 2007 09:24 PM
Unregistered
rubber mallet

l build boards for a living and give the fin a whack with a rubber mallet.All fin brands have fitted so far in chinook boxes.
29th August 2007 07:03 PM
Erik Loots Sanding your finhead... there was an intresting story in the dutch surfmagazine about that (written by some very fast guys)

It was about this (till it fits) :

1) start with the width of your finhead
2) make the top of your finhead bit round (like tectonics)
3) (if is still doesnt fit) sand the backside of your finhead till it fits properly.

I have seen people go very fast with a fin that wasnt very tight in the finbox...
I have seen people go very fast with a fin to deep in the finbox...
I have seen people with fins that where so tight in the box that the hard foam around the box damaged
I have seen people that need about 20 min for fitting fin properly (every time)

There is some middle in sanding where the fin will fit most boards (99%). THat is for me:

bit tight in my Carbon Art boards. (I once forgot the screws and did 65kmh/36kn and fin was still in finbox)
bit less tight in my Starboard Isonic 2006
29th August 2007 06:55 PM
martwald
Unable to use fin

Well I guess the fact that a pair of select fins I purchased before going to Weymouth last year were so far off that after a hour of sanding I still couldn't use them (I only noticed the poor fit at the event) and so I stuck with the stock fins.

The simple fact is that they should fit and you shouldn't have to sand a whole lot. I understand that a little bit of sanding being required isn't a bad thing, ensures a perfect fit, but the requirement of an electric sander and lots of time seems excessive???
29th August 2007 06:26 PM
WSguy
Quote:
Originally Posted by Unregistered View Post
I have had the same problem with Tectonic fins as well as Vector fins,all needed sanding to fit into my boards.The same goes for friends who have purchased these fins.
Recently I had to sand down a Tectonic fin to fit a Naish board. It's no big deal, though. I was a bit frightened that I took too much off with the disk sander on the electric drill, but it fits quite well in the box now. I can't see why you guys find this important.
This thread has more than 10 replies. Click here to review the whole thread.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT +7. The time now is 12:11 AM.