|7th April 2008 06:29 PM|
Too bad for you that the severne's come out of most tests much higher(performance wise)
|7th April 2008 04:40 PM|
Where are all these masts produced ?
Powerex in China ? Severne ??
|7th April 2008 11:03 AM|
|carvesalot||BOARDS magazine from the UK in the current issue does 400--460masts, last years May issue had the most comprehensive test I have ever seen on 16 masts. Unfortunate but neither test included a Severne. Your initial question is confusing, anyone would need more information , like are you interested in SDM or skinny, 50 75 100% carbon ?What length ? Boards report on P/X Wave RDM reads:: "Fairly middle of the road for bend curve, verging on flex top amd relatively stiff. the P/X is another middle ground mast that is likely to be more or less compatible with most sails. They have a great reputation for strength and durability." My collection of masts is almost all P/X , can't go wrong.|
|5th April 2008 12:08 PM|
|Unregistered||Instead off Powerex you also could consider an Epic gear mast. Comes from the Triana factory.|
|31st March 2008 11:24 PM|
In some cases there may be no difference, in other cases there may be quite a bit of difference.
Constant curve masts have about a 13% bend ratio.
How/where each loft specifies the top and bottom bends to equal 13% can vary significantly.
Some are softer in the top, but not so soft that the are "flex top".
Some are very constant curve and are as close to 13% throughout their entire length as it's posible to make them.
On the very high end of the spectrum, Powerex makes their own 100% Z-Speed masts.
Severne and Sailworks (and probably some others that I'm not familiar with) have their 100% carbon race masts made by Italica in Italy. Very nice masts but also very costly.
Each loft has masts made to their specifications and they test them to ensure that the company that makes them meets their specs.
Almost all std. dia masts are now constant curve so there may not be too much difference.
I use Powerex Z-Speeds, Sailworks Lightsticks (Itallica), Sailworks Speedsticks (Powerex), and Severne Redline (also Itallica) masts pretty much interchangeably, but there are minor differences in the way the sail looks, but nothing I have been able to detect on the water.
You will always "tune" your rig a bit, and when tuning you will focus on what you want.
More power= less downhaul and less top twist.
Better gust handling = less draft lower in the sail, more top twist.
Better high wind stability= more downhaul, more top twist, more panel tension top to bottom and a bit more outhaul to stabilize things.
So, to get the optimum performance (as designed into the rig by the loft) you probably will not go wrong using the recommended "best" mast, and this will always give you the best "starting point".
If the mast meets the design specs. (not all of them do) you can pretty much rig "by the numbers".
From there you will need to figure out what characteristics are the most important for you, on your boards, in your conditions. Then tune your rig to your personal specifications.
As far as which masts are "better", I would say the Powerex has consistently been the mast that more lofts specify as the "best alternate mast" if the loft has it's own brand.
If you use several different brands of sails and don't want to buy several different masts to go in them, then the Powerex masts seem to have the widest application range.
If you want to "rig by the numbers" then you are better off to buy the mast recommended as "best" from the loft that designed your sail.
The only other way to find out would be to get the "best" mast from the loft that designed your sail, and the "best alternate" mast from wherever, and have one of the high end sail lofts run a series of bend tests between the 2 different masts.
And, the results may vary depending on how the test is performed.
Some lofts run their tests with a simple weight at the 25%/50%/75% test points (with the mast suspended 5 cm from each end. This is the standard "Mast Check System" methodology.
Other lofts have gone to a jig that pulls the bend into the mast from the ends (just as downhauling does) and the results are different from the std. mast check system methodology.
Hope this helps,
|31st March 2008 09:30 PM|
That first link was interesting but it handled pretty old gear.
The others doesn't quite answer my question. I'm looking for the difference between these 2 masts, not masts in general. But thanx for the links anyway
|30th March 2008 03:47 AM|
More links on same site that explains more ...
|29th March 2008 12:36 PM|
Look at the crappy paint splattered all over many of the Severne Sails.
Would you really want to use their masts with a company that designs products like that?
They are more interested in trying to look good than improve performance (but they didn't realise it actually looks crappy as well).
I think you would be happy with the North, Gaastra or Maui Sails. The advantage of the Gaastra & Maui Sails is that you have a forum for support. Unfortunately no support with North except your local dealer who pretty much just has access to all the info that we read anyway - so it is not much help.
|28th March 2008 07:20 PM|
That link doesn't say much. It's pretty old masts there, but thank you anyway.
Would like some more feedback on this.
|28th March 2008 04:15 PM|
|This thread has more than 10 replies. Click here to review the whole thread.|