|24th July 2009 01:15 PM|
about 2010 Kode 68
Thanks for your comment.
However, I will sometime use Kode 68 on the plate water without wave. Thus, it is supposed to be better with back end of back footstrap on central position, right? Is it possible to fit the back end of back footstrape on certral position? Such as, to use different type of back footstrap or tool or..........
|22nd July 2009 08:58 PM|
Use the two supplied screws for the front set of plugs (for the back strap). For the rear, take the two screws out and put one of them in the middle hole that exist in the strap. Then mount that screw in one of the rear plugs (the one that is downwind on the way in with the waves).
You can use a single screw in front too (mounted centered in the strap), but that will mean more screws to move if you change to a location where the wind is from the other side.
|22nd July 2009 01:13 PM|
about the 2010 Kode
Could you please guide me how to fix the back footstrape? What I mean is how many screw used at front end of back footstrap with single central screw hole or both side hole at the end of back footstrap? I can't see any guide attached in my 2010 Kode 68 or in your website. Please let know how to do.
|18th July 2009 01:33 AM|
|17th July 2009 07:31 PM|
One thing to clear up here is:
There is no Kode 2010 yet in any website. You guys are talking about a 2009 Kode.
|17th July 2009 09:54 AM|
You're right about the 2010 Kode website. The graphic designers don't know the boards in detail well enough and with hundreds of boards to draw, this kind if things slip through. I'll have a chat with them and fix it up. The special features section too.
|14th July 2009 05:44 PM|
Oops, I meant the rear ones.
Or why not make a custom strap with wider base at the back.
|14th July 2009 05:40 PM|
Why can't the two front screw holes just be further apart..?
Also on a related but different subject, why oh why does the 102 Kode (which has a sail range up to 7.5) use US Box fins??? That is mental. I would consider one to go alongside my K86 if it had Tuttle box (or preferably power box), but not with the US box. What was the logic behind this?
|14th July 2009 02:45 PM|
about 2010 Kode 68
Thanks for your kindly explanation, but I am still confused. My questiions are as below.
1. The back footstarp is supposed to be fit on the central line of the board with single screw on each end if there is no enought room for double screw on each end. The space on central line of board has the most room for insert and screw.
2. Why the specification of 2010 Kode 68 on your website didn't show the back footstrap shift? Your photo show 2010 Kode 68's back footstrap on right central line of board. Why?
3. The special feature of 2010's Kode on your website does highlight Kode 68 with double screw on back footstrap, not single screw on each end?
|13th July 2009 11:24 AM|
The Kode 68 is designed to have an extremely thin tail and this mean that there isn't enough room for both the inserts and the finbox. If we increased the tail thickness, this would have affected the performance of the board so the solution was to offset the back holes.
The back strap needs to be fitted with only one screw on each end (so not double screws) and at an angle: using for example the left side on the front and the right side on the back, when lookng at the board from the deck. It will seem like a strange idea but once you've fitted the strap in this offset way and used it, it works just like a normal strap but still have the benefit of a super thin tail.
I hope this info will be of help to you. Cheers.
|This thread has more than 10 replies. Click here to review the whole thread.|