|14th January 2010 09:48 PM|
It's mainly a weight thing. The fcs fins are a lot lighter (the base of a MT fin weight a fair bit) as are the box installation. So it's a trade off. Another plus for the fcs system if of course availability which means that if you break one, is normally very easy to get a replacement.
But as you say, more trim options would be nice. Personally I think a new type of box with both lighter weight and some adjustability should be developed. The US but is good but just too heavy if we want four of them. The MT is pretty light and strong and easy to use, but lacks adjustability.
I don't think the fcs fins will break from landing jumps though. They are more solid than you might think and there are after all four fins to split the forces.
|14th January 2010 06:54 PM|
why not use mini tuttle boxes for the back fins?
isn't it much easier to have the same box system front and back?
then, if i imagine landing high jumps, i guess the fcs fins will brake sometimes!
additionally it could open more tuning possibilities (e.g. exchanging front and back fins)
and did you try asymmetrical frontfins with some toe-in?
|11th January 2010 10:48 PM|
Could you please post a picture of the sail cloth you use I can't seem to find the material you are talking about. Could you also post a picture of how you slip it in, this would be a great help.
|17th December 2009 03:15 PM|
|CornishAlex||What is happening to you happened to me (and to everyone I have spoken to who has a Quad including Timo Mullen). It happened to me for the first five or six sessions. Since putting in the sail cloth I have never (sailed the quad maybe twenty sessions since) had to re-tighten the back two fins. Slipping in some sail cloth to makes the fit in the box snugger. It is not the screw that is the issue its the size of the box being slightly to large for the fin so there is some flex, this works away lossening the fin screw after a session or two. If you make the fin sit more snugly into the box then the screw only has to hold it in place rather than trying to keep it tight. Try it (in my Ezzy sailbags there was a small bit of cloth with some instructions printed on it of how to thread your mast extension properly, that is perfect, cut a small piece off which you wrap around the base of the fin and push the fin snuggly into the box, you can not see it once its in place - if you do not sail on ezzy's ask someone at the beach who does.............).|
|17th December 2009 12:34 AM|
|Unregistered||ok thank you very much. I certainly have not broken the screw!! Yes they do tend to lossen after i while so I will tighten them again after a few session.|
|16th December 2009 09:28 PM|
|Ola_H||Even for foot strap screws you have to put some feel into it. As tight as possible could mean you break the screw if you're strong enough and have a good enough screwdriver. Pretty tight and then re-tighten after each of the first few outings is what I would say.|
|16th December 2009 05:32 PM|
For the front ones I tightend them until I felt the screw driver was about to slip. But I won't tighten them anymore as this felt right. For the footstrap screws do you tighten them as tight as possible?
|16th December 2009 06:34 AM|
You can safely leave your fins in.
WHen it comes to "how tight" its just impossible to say in words. For the rear fins with oiled screws, I would say snug and then e little bit more. Like FCS.
Front fins can be tighten harder, just don't let the screwdriver slip and mess up the screw.
|16th December 2009 01:29 AM|
How tight are u meant to tighten both sets of fins on the quad? The FCS system fins i tightended until it stopped but without applying too much force. For the front fins I tightened them fairly tight. Is this right. Also, is it ok to leave your fins in their boxes or is it reccomended you take them out after each session?
I had the same issue aas ola and the olive oil does work!
|28th November 2009 06:26 PM|
I have had a Quad for three months and used it loads due to an excellent November in the UK. Certainly this "is" a definite but minor issue. On the back boxes and fins do work loose. I eventually slipped the fins into the boxes with some sail cloth to make them a very tight fit, which is what one used to do with fins back in the old days to tighten them up. This worked perfectly and has stopped me having to tighten the screws continually (and worrying I was going to eventually strip the treads!!). I leave the fins in the board all the time never take them out.
This works fine, as I say its a minor teething issue and there are bound to be those with revolutionary new designs........its an amazing board totally made for the real world wave sailors just like the EVO was.
|This thread has more than 10 replies. Click here to review the whole thread.|