Starboard Forums

Starboard Forums (http://www.star-board-windsurfing.com/forum/index.php)
-   Free Forum (http://www.star-board-windsurfing.com/forum/forumdisplay.php?f=9)
-   -   Screws straps on futura Y2009 (http://www.star-board-windsurfing.com/forum/showthread.php?t=12020)

Unregistered 5th May 2011 04:13 PM

Screws straps on futura Y2009
 
Finally i have bought my first futura 111. I have found a new board in a shop edition 2009.
I have read maybe some problems with the screws of footstraps. More shorter.
Is it true?
When the board arrive and i fixe the straps i use originale screws or i must search other screws in winsurfing shop?
On this board, usually, where is the best position for the footstraps?

Roger 5th May 2011 07:34 PM

There are really no problems with the footstrap screws.
If you get the 6mm Plastics Technology (PT) x 28 mm screws and install them correctly, using a regular
#3 Phillips screwdriver, lubricating the threads with a bar of soap, and retightening after an hour or 2 on the water, the screws will last the life of your new board.
Also using a vice or vice grips to compress the K9 locks up into the footstrap webbing so the screws get a good start in the insert is recommended.
If you receive the newer 7 mm x 32 mm PT screws, and install them correctly you will have no issues beyond they are very hard to install the first time.
SO:
1/ Take one screw out of the footstrap, lube it with soap, and screw it (bare) down into each hole you intend to use for your footstrap positioning. You don't need to let the screw "bottom out" but just screw it in about half way to put some threads (like you would with a tap in a piece of metal) in the holes.
2/ Compress the K9 locks into the footstrap webbing using 2 pair of vice grips or a vice of some sort.
3/ Lubricate each screw with a bar of soap before installing.
4/ Retighten all you footstrap screws after an hour or 2 of sailing the board.

As to foostrap positioning, that depends on your size (height and leg length really) to get the spacing between front a back straps the most comfortable.
The you need to decide how tight you want the straps on your foot.
Some like them tight on both sides of the foot, others (like me) like them spread out at least one hole
wider than standard so I can turn my foot a little to apply pressure to the boad with my heel in different positions.
Then you may want to try a couple of different positions, in different conditions, to see what effect it has on the board.
I normally set up all my demo boards with the back strap rear screw in the middle position and the back strap front screw one hole forward of the middle position.
For the front straps, I put the outside screw in the back hole in the outboard positon and the inner screws in the middle position.
Seems to work pretty well for the majority of demo riders.
Hope this helps,

Unregistered 5th May 2011 10:01 PM

Thanks for all.
what is K9??

Roger 6th May 2011 07:35 PM

Hi Unreg,
The K9 anti-twist locks are the plastic washers with a tang on the underside and 4 "canine teeth spikes on the upper side that lock into the footstrap inserts on the board and the spikes stick up and engage the nylon webbing in the footstrap.
They keep the footstrap from twisting.
The are shown on the RH bottom of this link page:

http://www.star-board.com/SpringSumm...gn_details.php
Hope this helps,
Roger

Unregistered 6th May 2011 09:27 PM

ok thanks Roger. Now i have understand. :o))


All times are GMT +7. The time now is 10:04 AM.

Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.