Starboard Forums

Starboard Forums (http://www.star-board-windsurfing.com/forum/index.php)
-   Free Forum (http://www.star-board-windsurfing.com/forum/forumdisplay.php?f=9)
-   -   Remi - R13 Soft vs R19 Soft on F160 (http://www.star-board-windsurfing.com/forum/showthread.php?t=3942)

Unregistered 28th May 2008 03:05 PM

Remi - R13 Soft vs R19 Soft on F160
 
Dear Remi

I am considering little change within my fin's quiver.

Currently I am using R13M+8 and it looks that I am missing some power during light wind racing on F160. Apart from the right technique and TOW, I thought I would get a more powerfull fin. I could easily get R13 Soft -- or R19 Soft -- and would like to know your comments. What is the best option out there, which find would you reccomend the most...

Sailing on RS Racing 10.7 and my weight is round 75kg; flat to choppy water up to 18knots; occasionally racing in Baltic see..

I look forward to hearing from you and others.

Regards

Tomek M

Remi 28th May 2008 10:29 PM

Hi Tomek,

For really light winds for your weight, you can use the R19 soft-- Rake +8cm until 12 knots max and after go fo your R13 M +8. I recommand you to change the angle of the R13M to +6cm, you will be more faster.

All the best

Ken 29th May 2008 12:38 AM

Remi,

I have an R13M, which I bought about about 4 years ago. I got if from Sailworks and didn't know anything about rake at the time and they didn't offer any information. I don't know what the rake for this fin is. I guess it was the standard rake at the time. Can you help?

Thanks,

Ken

G-42 29th May 2008 02:15 AM

Quote:

Originally Posted by Ken (Post 22308)
Remi,

I have an R13M, which I bought about about 4 years ago. I got if from Sailworks and didn't know anything about rake at the time and they didn't offer any information. I don't know what the rake for this fin is. I guess it was the standard rake at the time. Can you help?

Thanks,

Ken

Ken,
give Bruce a call at the Sailworks loft (541-386-6561); he'll be able to tell you. There was the old 'standard' rake (the very first R13's), which became the basis for all the +x nomenclature. Then at some point (and I believe that was right around the time you're referencing - around 04 or 05), the "standard" rake for new R13's was changed to something like +2 or +3. I remember having a conversation with Bruce about it, so I'm sure he'll be able to tell you.

-Andreas

http://g-42.blogspot.com

Ken 29th May 2008 05:01 AM

G-42,

Thanks for you response. I may check with Bruce, but it was more curiosity than anything. I have been happy with the fin, but wondered what the difference was between my fin and the R13m +6 that Remi suggested for Tomek since I weigh 79 kg and also have a 160.

SeanAUS120 29th May 2008 01:33 PM

@ Unregistered - If you are mostly sailing in >10 knots, I would go with the R13 S--. In flex-stiffness, the R13 will be considerably softer than the R19 because the foil is thinner and has less area. The R13 is a very versatile fin and works in nearly all conditions and requires minimal tuning from the rider to get up to speed.

Remi is right, for lightwinds the R19 would be better, but if you were only going to buy ONE fin, I would think you'd get more out of the R13 across the different conditions. Make sure you go for an S-- as in the 160 it really appreciates a soft fin for power. This will be suitable even in strong winds and you still have your R13M if you prefer that as the wind gets up.

@ Ken - put your R13M in your board and put a straight ruler at the front of your fin from the bottom of the board perpindicular to the board. With another ruler, measure the distance from vertical to your fin tip. Like this photo: http://www.carbonsugar.com/wp-conten...08/04/rake.jpg - although, measure the TIP not 15cm down from the tip like in this photo.

A Deboichet fin at +11cm is raked at vertical. So a fin at +8cm would be 30mm from vertical. +6cm = 50mm from vertical etc etc. That way you can find what rake your fin is regardless of its vintage.

You can change the rake a little by sanding the front/back of the fin head and kicking it forward in your finbox but changing the rake anymore than 1.5cm requires you to drill out your fin bolt holes in the fin head as they will no longer line up with your board holes.

There's some more info about what rake and stiffness does to fins and to your boards in an article I wrote here if this helps:

http://www.carbonsugar.com/design/ev...about-fw-fins/

Ken 29th May 2008 10:39 PM

SeanAUS120,

Great information, Thanks a lot. However, I am a little confused by your statement:

"A Deboichet fin at +11cm is raked at vertical. So a fin at +8cm would be 30mm from vertical".

How is +11cm vertical? Wouldn't vertical be +0 (leading edge at 90 degrees from the board)?

Thanks,

Ken

Otrebla 30th May 2008 02:51 AM

Ken,
the measurement of the rake is for some reason "inverted": a higher number means a more upright leading edge, and a lower number a more raked fin.
I was a bit confused too, but there's a wonderful article on carbonsugar.com about fins and fin-related measurements that explains everything. Really worth a read.
Cheers!

SeanAUS120 30th May 2008 10:33 PM

Hi Ken,

Yes, you are right, 90 degrees to the board is vertical, however Deboichet uses a scale that doesn't refer to angles or vertical at all; it can be a little confusing!

I don't know exactly how it came about, but basically back about 4-5 years when everyone started changing the rake of their fins to be more upright, Deboichet fins were about the only decent fins on the market and so people started saying "my fin is +2 or +4cm", which meant that their fin was 2cm more upright than the "original" fin was designed.

Eventually, this became a little more standardised (thank god!) and the popular Deboichet system used now is +11cm as vertical (although most fins are usually +6cm or +8cm) which is just a reflection of how far the fin is raked upright compared to the "original mould". Its a confusing scale as it doesn't reflect AT ALL how "upright" the fin is. It merely refers to the original rake on the fin mould (although this has somewhat changed over the years).

I prefer to talk in degrees where 0 degrees is vertical and 2.5 degrees is roughly a +8cm Deboichet fin (or 30mm back from vertical at the tip) as this is less confusing. The Deboichet rake system only applies to Deboichet fins!

I just mentioned the 30mm back from vertical just to show you that this is what is considered "+8cm" right now, as I'm sure if you have a Deboichet fin from 4-5 years back it might not be the same "original rake" as a fin that is made now.

Does that make sense?

Ken 30th May 2008 11:36 PM

Otrebla, Sean,

Thanks guys, I now get it. It seems like they should make a change at some point to a more logical measuring system.

Ken


All times are GMT +7. The time now is 03:35 PM.

Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.