Starboard Forums

Starboard Forums (http://www.star-board-windsurfing.com/forum/index.php)
-   Free Forum (http://www.star-board-windsurfing.com/forum/forumdisplay.php?f=9)
-   -   fins and footdtraps (http://www.star-board-windsurfing.com/forum/showthread.php?t=3968)

windfrancois 2nd June 2008 12:12 AM

fins and footdtraps
 
Hi,

I am coming back to windsurf after 16 years (I used an Electric Rock in 1990). Need to know how to select my fins regarding the wind, waves and sail sizes. I have: Carve 144 DRAM, Hypersonic 111 Wood, Severne Focus 7,5 (wish alu + mast 30% Carbon), Neil Pryde V8 9,0 (full Carbon). I sail on a small lake with chops, lightwind not regular. I weight 90kg, level waterstart and jibe.

Actually all my straps are forward maximum, is it OK, does it improve upwind sailing?

Thank you

François

PGVirtual 2nd June 2008 02:44 AM

With the Carve 144 a good compromise size would be 46 cm, possibly 42 for the smaller sail and 48-50 for the 9.0. That is about the sensible range. Bigger fin for lighter winds and bigger sail, smaller fin when well powered up with the 7.5 sail.

They Hypersonic is quite a different design. It makes do with a lot smaller fins, maybe in the 30-35 cm range.

For best allround performance move your straps back a little, to the mid positions. That usually gives a more natural stance.

windfrancois 2nd June 2008 03:17 AM

Thany you,

Another question, do the fins and so the board, may be polished or a little rough to prevent spin out and improve speed. In fact is it possible to spin out with so big fins?

Unregistered 2nd June 2008 03:23 AM

Shouldn't be "Fins and foodtraps"?

windfrancois 2nd June 2008 05:25 AM

keybord error Fins an footstraps!! I don't like Foodtraps (I am dentist).

James 2nd June 2008 05:54 AM

Francois- This spreadsheet calculates the correct size fins to be used with different size sails.

http://www.vims.edu/general/sailpadd...Calculator.xls

Straps forward will not help your upwind performance, but it may help you get accustomed to sailing a modern board. When you are comfortable with the forward, inboard positions on your 144 you should move the straps back and out for better speed and upwind performance. I.e. the straps should be where they are in the picture here:

http://2006.star-board.com/products/carve.asp

As PG notes, for the hypersonic you can use a somewhat shorter fin than recommended; perhaps 6 cm shorter, but it works ok with normal length fins, too. When I had a hypersonic it came with 2 fins; a 34 cm and a 44 cm. I used the 44 cm fin with sails 7.5 - 9.4, and I used the 34 cm fin with sails 5.2 - 6.6. I don't know if you've sailed the hypersonic much yet, but I have to warn you that it's a very difficult and technical ride which is sensitive to where you put the mast base, how you rig the sail, what size fin you have, where the footstraps are, etc. It will take a lot of trial and error to figure out what settings work best for you.

Good luck!

windfrancois 2nd June 2008 06:46 AM

WOW

That calculator is very impressive. You may be either a doctor in maths or a nerd windsurfer!!!!

thanks to all, things become easier to make sense now.

James 2nd June 2008 08:58 AM

Well, I'm definitely not a doctor in maths... :) I'm a nerd windsurfer working on my doctorate in biology.

Roger 4th June 2008 10:45 PM

Hi windfrancois,
I think the current wisdom on "surface finishes" for windsurf gear/hi speed sailing dinghys/huge racing yachts is that a polished surface is too smooth and actually cuts down your speed.
Using a "figure 8" pattern with 400 wet/dry abrasive cloth is about the best you can do.
Some folks like a straight pattern in line with the water flow.
The idea is to create a little "tooth" (microscopic maybe, but "tooth" just the same) to hold a boundary layer of water molecules on the surface.
Testing has shown that water has less "friction" on a fully wetted out boundary layer than on a polished surface with no boundary layer or "wet out".
Surface finish can have a positive effect on preventing spin out, but mostly spin out
is due to imperfections in either the foil or the planform of the fin.
Hope this helps,

windfrancois 7th June 2008 04:24 PM

Thank you Roger, I was not sure that this concept was still on the edge. I remember some experiments about a membrane on sailboats with microscopic triangular channels to retain more water layer do you know something about this research.


All times are GMT +7. The time now is 02:51 AM.

Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.