Go Back   Starboard Forums > Windsurfing School

Reply
 
Thread Tools Display Modes
Old 28th December 2007, 10:50 PM   #1
Sam J
New Member
 
Join Date: May 2007
Posts: 6
Default Sticky Mast

Hi Roger
I recently bought a new Tushingham TK mast. Ever since I used it once on the coast it has been very hard to separate. What do you recomend i do?
Thanks Sam J
Sam J is offline   Reply With Quote
Old 29th December 2007, 09:27 AM   #2
Roger
Dream Team - School Guru
 
Join Date: Aug 2006
Posts: 2,105
Default

Hi Sam J
First, did you rig it the first time on the sand or did you somehow get sand in the joint the first time you rigged the new TK mast?
The fit of the ferrule on a carbon mast is a pretty close tolerance affair, and if you get any sand in between the male and female diameters, when the mast is bent (like you left in in the shallow "wash" at the edge of the water with the sail rigged) it can be very difficult (impossible in some cases without using some extreme measures) to separate the mast as tiny grains of sand and grit get into the slight opening at the front of the mast (even inside the luff sleeve) and then when you let off the dowhaul, the slight opening closes up and traps or embeds the grit in the joint.
If you have your mast apart, take a bar of soap (plain 'ol bath soap) and rub the soap on the outside diameter of the male portion of your ferrule.
Now put the mast together and twist the top and the bottom sections a few times.
Then take the mast apart and look for dark shiny spots on the male portion of the ferrule.
These are the "tight spots"!
Now take a smooth flat file and gently work the "tight or high" spots down a couple of strokes of the file at a time (just take off the shiny spots so they blend with the surrounding areas of the diameter.)
This should free up your mast, and make it very easy to take apart when it's "clean" and there's no grit in the joint.
To positively "eliminate" this problem, get a roll of vinyl electrical tape and wrap the joint of your mast (with the ferrule tightly pushed together) with a couple of wraps of the tape.
This will exclude any grit and ensure that the mast does not take on any water at the ferrule.
You can use the tape several times if you are careful when you take it off after the mast is out of the sail when derigging.
This process and the "tape trick" have been making my life easier for many years and I sometimes have as many as a dozen mast to take apart at the end of a big demo day.
Hope this helps,
Roger is offline   Reply With Quote
Old 29th December 2007, 04:00 PM   #3
crazychemical
Member
 
Join Date: Nov 2006
Location: Zaventem, Belgium
Posts: 352
Default

what i always do when i go windsurfing at sea:
when i take out my mast, i clean the parths that need to be joined with my hand so all the sand is off from both joining sides. I put the mast together, turn it a few times in both directions and take the mast appart again to see if it still has sand somewhere, clean it again with my hand and put it back together. After that i quickly, without putting the mast down take some ducktape around the joint so nothing can get it.
Also when you can't get the mast appart sometimes it's because of salt (but this should only be in warm places where the water had a bigger chance of evaporating). The thing i found worked was to get a few strong ppl (you have no idea how big some saltcristals can get) and but the joint under a fresh water tap and let the water run (i know, it's spilling, so sue me) whilst you try to twist the mast in opposite directions (one half clockwise, the other anticlockwise). Once you can twist the mast, you can pull it appart.

hope it helps!

cheers and happy NY!
__________________
Haiko, AKA crazychemical
crazychemical is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +7. The time now is 03:29 PM.