Go Back   Starboard Forums > Ask Our Team

Reply
 
Thread Tools Display Modes
Old 22nd March 2007, 05:43 PM   #1
michele
New Member
 
Join Date: Mar 2007
Posts: 6
Default Carve 121 set up

Dear friends,
in date 9/24/2003 I write you a post about the set un of Carve 121.
I've two questions:
1) Roger sad me: "back i fast....move the mast foot all the way back until it?s about to pop out the reare of the narrow parte of the slot T-nut access. Well, when he said "pop out" is intending the screw of the mast base or the reare parte of the mast twins plate ?

2) Roger write me "look to see where the water is coming out frome under your board when you are fully planing. If its coming out ahead of the front footstraps ...then you need to get both your wheigt and mast foot pressure back...." Well I,ve try to poot all the wai back but the water go out ahead or under the front foot strap and the board is non free to run (realy) on the fin. (not very loose feel) Why ? Do you think that the problem is a too much hight boom and too much shorter arnes line ? (24")

Thank,
Michele
michele is offline   Reply With Quote
Old 23rd March 2007, 09:16 AM   #2
Roger
Dream Team - School Guru
 
Join Date: Aug 2006
Posts: 2,112
Default RE: Carve 121 set up

Hello Michele,
Question 1) You can move the mast base all the way back until the "T"-nut is at the back of the slot, but not hanging over into the wider access slot.
This will put the rear edge of the twist plate all the way back until it's near or slightly over the serial number (on some boards, as the serial numbers have moved around a bit over the years).
What year Carve 121 do you have? I did a little research, and since your first post was in 2003 I'll take a chance that you have a 2003 Carve 121.
If you only move the mast foot back until the edge of the twist plate is at the back of the wider access slot, youi can still go back around one more inch.
You can move the mast foot back until you feel a little tab (on some boards) at the back of the mast slot. You do not want the T-nut hanging over into the unsupporting access slot, but as long as there's full contact between the underside of the "T"'s on the nut and the mast slot, you are OK.
Question 2)
Ummmm... I'd have to see you in action, fully lit up on an "appropriate for the conditions" rig/board/fin to tell if the reason your board is not "unwetting" fully is due to the tuning of the board/ rig/fin, or due to how you are trying to sail it (stance, harness line position and length, and perhaps footstrap position.
How much do you weigh...?
What size rig (s) are you using...?
What is the approximate windspeed...?
When you are really powered up, you normally would feel the board trying to "tailwalk" a little with the mast foot all the way back and (again "normally") you would want to move the mast foot forward a bit to "settle" your board.
What fin are you using...?
Where do you have the footstraps positioned...?
Are you tall, with long legs, or shorter...?
Sorry I don't have a more specific answer, but your situation is so "dynamic" there could be any number of things "unbalanced" and then again maybe nothing is out of tune and you need to place your weight differently, change you stance a little or something similar.
Water coming out "under the front footstraps" is very close to optimum, so you can't be having too big a problem with your issues here.
Hope this helps,
Roger is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +7. The time now is 08:48 PM.