Old 5th September 2007, 07:42 AM   #1
Joe
Member
 
Join Date: Aug 2006
Posts: 64
Default Replace Barrel Nut?

Hi Roger - hope you are feeling better.

Quick question - can I punch out the barrel nut in a deep tuttle fin and insert another one?

I've stripped the front barrel nut on my 70cm drake.

I have a barrel nut from the original 64cm fin that I don't like to use.

Thanks for you help.

Regards,
Joe
Joe is offline   Reply With Quote
Old 6th September 2007, 12:11 AM   #2
o2bnme
Member
 
Join Date: Aug 2006
Location: Maine & North Carolina
Posts: 230
Send a message via AIM to o2bnme Send a message via Yahoo to o2bnme
Default

I'm not Roger, but I can answer. You can replace the barrel nuts in your fins. I've done a lot of this in an constant battle to get all fins to use the same type of bolts. Take a flat screw driver and hammer to pound out the old bolt. Some are looser than others.
__________________
Starboard [Gemini, F-Type 148, iSonic 105], AHD [Convert 60, GT Special 73], Windsurfer
Neil Pryde [v8 9.8], Sailworks [Retro 8.0; Hucker 6.6, 5.6, 4.8]


To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
o2bnme is offline   Reply With Quote
Old 6th September 2007, 03:57 AM   #3
Ellen Faller
Dream Team - School
 
Join Date: Aug 2006
Posts: 75
Default

I'm not Roger either, but o2bnme is totally right. I've done it many times myself. Some people like to change them all for US, and others want all metric. And then there are the folks who try to screw a US bolt into a metric nut and mess things up.
Ellen Faller is offline   Reply With Quote
Old 6th September 2007, 04:06 AM   #4
Joe
Member
 
Join Date: Aug 2006
Posts: 64
Default

Thank you! I will attempt tonight...
Joe is offline   Reply With Quote
Old 6th September 2007, 07:15 AM   #5
Roger
Dream Team - School Guru
 
Join Date: Aug 2006
Posts: 2,092
Default

Hi Joe,
What Bill and Ellen suggest will work nicely.
Only thing I would sugest isthat you get a "pin drive punch" just slightly smaller than the outside diameter of the brass barrel nut.
With the pin drive punch, the punch will stay nearly centered in the hole and do a much nicer job of "driving" the old nut out and the new nut in.
Just be sure when you install the new barrel nut that you get it started nice and straight. If you get it started in the hole at an angle or cockeyed, it will damage the hole.
A good trick to use here is the apply some soap in the hole and a little soap on the outside of the barrel nut as a "lubricant" to allow the brass barrel nut to slide in more easily.
Be sure to align the threads to the top of the fin and the fin screw hole in the board's deck before you drive the barrel nut in.
Best way to do this is to mark the screwdriver slot before you drive the old nut out.
Hope this helps,
Roger is offline   Reply With Quote
Old 7th September 2007, 06:48 AM   #6
Joe
Member
 
Join Date: Aug 2006
Posts: 64
Default

Done - perfect fit - thanks!
Joe is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +7. The time now is 07:41 PM.